物性表自定义
公司信息及水印
公司信息及水印
下载中文物性表
下载英文物性表
邮件发送/他人
| 牌号简介 About |
|---|
| Bormed™ TD109CF是一种丙烯-α-烯烃共聚物。适用于冷辊法无取向铸膜、管式水淬法吹膜及BOPP薄膜的生产。 Bormed TD109CF is a propylene alpha olefin copolymer. This grade is suitable for the manufacturing of non-oriented cast films on chill roll process and blown films on tubular water quenching process. CAS-No.: 25895-47-0 Applications Bormed TD109CF has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed TD109CF . Medical device packaging Pouches for IV solutions This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features Excellent optical properties Wide sealing window Low sealing initiation temperature Sterilisability by means of water steam High seal strength and hot tack force |
产品描述 Product Description
用途：薄膜;流延薄膜;医用包装;
加工条件：吹塑薄膜
性能特点： 耐低温热封性; 透湿性差; 蒸汽消毒; 共聚物; 热粘性强; 密封范围宽; 光学性能; 热封性好; Good heat sealing,Steam sterilized,Optical performance,Thermal viscous strength,Poor moisture permeability,Broad Seal Range,Copolymer,Low temperature heat sealing
| 技术参数 Technical Data | |||
|---|---|---|---|
|
物理性能 PHYSICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
|
熔体质量流动速率 Melt Flow Rate |
|||
|
230℃，2.16kg 230℃，2.16kg |
6.0 | g/10min | ISO 1133 |
|
机械性能 MECHANICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
|
弯曲模量 Flexural Modulus |
|||
|
23℃，注塑成型 23 ℃, injection molding |
700 | MPa | ISO 178 |
|
摩擦系数 Frictional coefficient |
|||
|
与自身 - 动态 With oneself - dynamic |
> 0.70 | ISO 8295 | |
|
薄膜 film |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
|
拉伸模量 Tensile modulus |
ISO 527-3 | ||
|
MD，50 µm MD，50 µm |
470 | MPa | ISO 527-3 |
|
TD，50 µm TD，50 µm |
490 | MPa | ISO 527-3 |
|
拉伸强度 tensile strength |
ISO 527-3 | ||
|
MD，50 µm MD，50 µm |
MPa | ISO 527-3 | |
|
TD，50 µm TD，50 µm |
MPa | ISO 527-3 | |
|
拉伸应变 Tensile strain |
ISO 527-3 | ||
|
MD，断裂，50 µm MD, fracture, 50 µ m |
% | ISO 527-3 | |
|
TD，断裂，50 µm TD, fracture, 50 µ m |
% | ISO 527-3 | |
|
装有测量仪表的落镖冲击 Dart impact equipped with measuring instruments |
|||
|
50 µm，Total Energy 50 µm，Total Energy |
J | ISO 7765-2 | |
|
热性能 THERMAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
|
熔融温度 Melting temperature |
℃ | ISO 11357-3 | |
|
光学性能 OPTICAL |
额定值 Nominal Value |
单位 Units |
测试方法 Test Method |
|
光泽度 gloss |
|||
|
20°，50 µm 20°，50 µm |
ASTM D2457 | ||
|
雾度 Haze |
|||
|
50 µm 50 µm |
% | ASTM D1003 | |
| 备注 |
|---|
| 1 一般属性：这些不能被视为规格。 |
|
【新闻资讯】查看全部
江氏企业申报出口乙烯-丙烯共聚物再生颗粒50.1吨
2018-11-23 金陵海关日前查获违规进口废塑料百余吨，目前案件已移交海关缉私部门处理。 不久前，江苏两家企业分别向南京海关隶属金陵海关驻新生圩办事处申报进口乙烯-丙烯共聚物再生颗粒50.1吨和50.8吨，两批货物境内收货人不同，但境外发货人、品名规格、船名航次均相同且提单号接近。海关人员经前期风险分析及现场查验，发现货物明显存在非树脂固态杂质，外观呈非均质颗粒状，具有较大的固体废物特征。经认定，这两批货物实际为再生过程中缺乏质量控制的不合格品或塑料的废碎料及下脚料，属于国家限制进口类可用作 |
|
【免责声明】 广州搜料信息技术有限公司保留所有权利。 此数据表中的信息由搜料网soliao.com从该材料的生产商处获得。搜料网soliao.com尽最大努力确保此数据的准确性。 但是搜料公司对这些数据值及建议等给用户带来的不确定因素和后果不承担任何责任，并强烈建议在最终选择材料前，就数据值与材料供应商进行验证。 |
当前牌号已加入对比
支付宝
微信支付